Baldor NM3455 .25HP, 1140RPM, 3PH, 60HZ, 48, 3411M, TENV, F1 Paper & Corrugated

Baldor NM3455 .25HP, 1140RPM, 3PH, 60HZ, 48, 3411M, TENV, F1 Paper & CorrugatedSpecs Output @ Frequency . 250 HP @ 60 HZ Phase 3 Synchronous Speed @ Frequency 1200 RPM @ 60 HZ Voltage @ Frequency 460. 0 V @ 60 HZ 230. 0 V @ 60 HZ XP Class and Group None XP Division Not Applicable Agency Approvals CSA UR Ambient Temperature 40 C Auxillary Box No Auxillary Box Auxillary Box Lead Termination None Base Indicator Rigid Bearing Grease Type Polyrex EM ( 20F +300F) Blower None Current @ Voltage 1. 400 A @ 230. 0 V 1. 600 A @ 208. 0 V .

8 a Front Face Code Resilient Mount Front Shaft Indicator None Heater Indicator No Heater Insulation Class B Inverter Code Not Inverter KVA Code F Lifting Lugs No Lifting Lugs Locked Bearing Indicator No Locked Bearing Motor Lead Exit Terminal Panel Motor Lead Termination Flying Leads Motor Lead Quantity/Wire Size 7 @ 18 AWG Motor Type 3421C Mounting Arrangement F1 Number of Poles 6 Overall Length 11

CAT NO IDWNM22937T SPEC

Frame Material Cast Iron Impregnation Method Dip and Bake Polyester Regreasing System At Drive end and Non-drive end Main terminal box hole NPT 1 1/2" Terminal Block Without Shaft Locking Device Without Shaft Material SAE 1040/45 Carbon Steel Painting RAL 3002 203A (ISO 12944 - C2) Grounding Lugs Single Fan Cover material Without Fan Cover Tropicalized Painting Without Fan material Without fan Bearing cap Yes- Bearing Cap Bolt Material Carbon Steel Balancing Method 1/2 Key Drip Cover Without Overload protector (phenolic) Without overload protector Connection Cables Quantity 6 Features

1 a Heater Indicator No Heater Insulation Class F Inverter Code Inverter Ready IP Rating IP55 KVA Code G Lifting Lugs Standard Lifting Lugs Motor Lead Quantity/Wire Size 3 @ 4 AWG Motor Type A36056M Mounting Arrangement F1 Number of Poles 2 Overall Length 31

CEM4108T SPEC

625 IN Shaft Extension Location Pulley End Shaft Ground Indicator No Shaft Grounding Shaft Rotation Reversible Shaft Slinger Indicator No Slinger Speed 1765 rpm Speed Code Single Speed Motor Standards NEMA Starting Method Direct on line Thermal Device - Bearing None Thermal Device - Winding None Vibration Sensor Indicator No Vibration Sensor Winding Thermal 1 None Winding Thermal 2 None XP Temp Code T4 Drawings

3 POLES 6 NUMBER SPEEDS 1 RPM 1190 RPM 2 1190 RPM 3 1185 RPM 4 985 RPM 5 985 HERTZ 60 HERTZ 2 50 VOLTS PRIMARY 230/460 VOLTS 460 VOLTS 2 230 VOLTS 3 208 VOLTS 4 400 VOLTS 5 200 FRME 365 SHAFT CODE T MOUNTING HORZ-FOOTED ASSEMBLY POSITION F1 MOTOR TYPE CTE OPPOSITE END BEARING 6213-2Z-J/C3 SHAFT END BEARING 6313-2Z-J/C3 AMBIENT 40 ROTATION DUAL SERVICE FACTOR 1

AOM3611T SPEC

Frame 364/5TSC Output 100 HP (75 kW) Number of Poles 2 Frequency 60 Hz Rated speed 3555 rpm Slip 1

Frame 315S/M Output 132 kW (175 HP) Number of Poles 6 Frequency 60 Hz Rated speed 1190 rpm Slip 0

875 IN Shaft Extension Location Pulley End Shaft Ground Indicator No Shaft Grounding Shaft Rotation Reversible Shaft Slinger Indicator Shaft Slinger Speed 1760 rpm Speed Code Single Speed Motor Standards NEMA Starting Method Direct on line Thermal Device - Bearing None Thermal Device - Winding Normally Closed Thermostat Vibration Sensor Indicator No Vibration Sensor Winding Thermal 1 None Winding Thermal 2 None Drawings

0 % Feedback Device NO FEEDBACK High Voltage Full Load Amps 76